You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
125 lines
3.9 KiB
125 lines
3.9 KiB
## Configuration file for CAVA. Default values are commented out. Use either ; or # for commenting. |
|
|
|
|
|
[general] |
|
|
|
# smoothing mode, can be normal, scientific or waves. |
|
; mode = normal |
|
|
|
# Framerate Default: 60. Accepts only non-negative values. |
|
; framerate = 60 |
|
|
|
# Sensitivity in %. If you think the bars are to low/response is to little, try |
|
# increasing this value 200 means double height. Accepts only non-negative values. |
|
; sensitivity = 100 |
|
|
|
# Autosens will attempt to decrease sensitivity if cava peaks. 1 = on, 0 = off |
|
; autosens = 1 |
|
|
|
# The number of bars (0-200). 0 (default) sets it to auto (fill up console). |
|
# width of bars and space between bars in number of characters. Default width 3 and space 1. |
|
; bars = 0 |
|
; bar_width = 3 |
|
; bar_spacing = 1 |
|
|
|
|
|
# Lower and higher cutoff frequencies for lowest and highest bars |
|
# the bandwith of the visualizer, defaults to 50 - 10000 Hz |
|
# Note: there is a minimum total bandwith of 43Mhz x number of bars. |
|
# Cava will automatically increase the higher cuttoff if a too low band is specified. |
|
; lower_cutoff_freq = 50 |
|
; higher_cutoff_freq = 10000 |
|
|
|
|
|
|
|
[input] |
|
|
|
# method of capturing audio, possible methods are: 'pulse', 'alsa' or 'fifo'. |
|
# Defaults to 'pulse', 'alsa' or 'fifo', in that order, dependent on what support cava was built with |
|
# |
|
# All input methods uses the same config variable 'source' |
|
# to define where it should get the audio. |
|
# |
|
# for pulseaudio 'source' will be the source. Default: 'auto', which uses the monitor source of the default sink |
|
# (all pulseaudio sinks(outputs) have 'monitor' sources(inputs) associated with them) |
|
# |
|
# for alsa 'source' will be the capture device. Default: 'hw:Loopback,1' |
|
# for fifo 'source' will be the path to fifo-file. Default: '/tmp/mpd.fifo' |
|
; method = pulse |
|
; source = auto |
|
|
|
; method = alsa |
|
; source = hw:Loopback,1 |
|
|
|
; method = fifo |
|
; source = /tmp/mpd.fifo |
|
|
|
|
|
|
|
[output] |
|
|
|
# ouput method may be ncurses, noncurses or raw. noncurses is for systems that does not suport ncurses. |
|
# raw is a 16 bit data stream of the bar heights that can be used to send to other applications |
|
# raw defaults to 200 bars, can be adjusted in the bars option above |
|
; method = ncurses |
|
|
|
# visual styles, may be 'stereo' or 'mono'. |
|
# Stereo mirrors both channels with low frequencies in center. |
|
# Mono averages both channels and outputs left to right lowest to highest frequencies |
|
; style = stereo |
|
|
|
# raw output target defaults to stdout, a fifo will be created if target does not exist |
|
; raw_target = /dev/stdout |
|
|
|
# raw data format, can be binary or ascii |
|
; data_format = binary |
|
|
|
# binary bit format, can be '8bit' (0-255) or '16bit' (0-65530) |
|
; bit_format = 16bit |
|
|
|
# ascii max value, in ascii mode range will run from 0 to value specified here |
|
; ascii_max_range = 1000 |
|
|
|
# ascii delimiters, in ascii format each bar and frame is separated by a delimiters. |
|
# use decimal value in ascii table (i.e. 59 = ';' and 10 = '\n' (line feed)) |
|
; bar_delimiter = 59 |
|
; frame_delimiter = 10 |
|
|
|
|
|
|
|
|
|
[color] |
|
|
|
# supported colors are: red, green, yellow, magenta, cyan, white, blue, black. |
|
; background = black |
|
; foreground = cyan |
|
|
|
|
|
[smoothing] |
|
|
|
# multiplier for the integral smoothing calculations. Takes values from 0 - 0.99. |
|
# Higher values means smoother, but less precise. 0 to disable. |
|
; integral = 0.7 |
|
|
|
# disables or enables the so-called "Monstercat smoothing". Default: 1. Set to 0 to disable. |
|
; monstercat = 1 |
|
|
|
# Set gravity multiplier for "drop off". Higher values means bars will drop faster. |
|
# Accepts only non-negative values. 0.5 means half gravity, 2 means double. Set to 0 to disable "drop off". |
|
; gravity = 1 |
|
|
|
|
|
# In bar height, bars that would have been lower that this will not be drawn. |
|
; ignore = 0 |
|
|
|
|
|
[eq] |
|
|
|
# This one is tricky. You can have as much keys as you want. |
|
# remember to uncomment more then one key! More keys = more precision. |
|
# Look at readme.md on github for further explanations and examples. |
|
; 1 = 1 # bass |
|
; 2 = 1 |
|
; 3 = 1 # midtone |
|
; 4 = 1 |
|
; 5 = 1 # treble
|
|
|